# Gear and Turn Signal Stalk

This is the installation guide for Tesla Model 3 (2024+) Gear and Turn Signal Stalk from EVOffer.

{% embed url="<https://evoffer.com/product/model-3-2024-gear-turn-signal-stalk/>" %}

## Packing List

1.
2.
3. <br>

## Recommended Tools <a href="#recommended-tools" id="recommended-tools"></a>

1. Small Flathead Screwdriver
2. Phillips Screwdriver
3. T-20 Screwdriver
4. T-45 Screwdriver (with long wrench)

## Installation

### Step 1 - Remove the Steering Wheel

Insert a small flathead screwdriver into the 2 holes behind the steering wheel to pop out the airbag.

<div><figure><img src="/files/YhlmEUBRsfGzXSDwX4K2" alt=""><figcaption></figcaption></figure> <figure><img src="/files/ZS7akaBMwvzYN4GSxhom" alt=""><figcaption></figcaption></figure></div>

Disconnect the yellow and red connectors.&#x20;

<figure><img src="/files/g42m6MIyUJonSxLCGY7b" alt="" width="563"><figcaption></figcaption></figure>

Remove the center screw with a T-45 screw driver with long wrench.

<div><figure><img src="/files/11WK9MqfIlHYj8hHCdR7" alt=""><figcaption></figcaption></figure> <figure><img src="/files/0IyHGo1frkQBKiozJN6Q" alt=""><figcaption></figcaption></figure></div>

Take a picture of the center screw position. You can refer to this picture when you put the steering wheel back later. Remove the steering wheel afterwards.

<div><figure><img src="/files/RZ0EPJjURnmfYpuRWKLD" alt="" width="563"><figcaption></figcaption></figure> <figure><img src="/files/6THUEIik4QWZQiisTBTx" alt=""><figcaption></figcaption></figure></div>

### Step 2 - Remove the Steering Column Covers

Pull the top cover outward to release the cover.

<div><figure><img src="/files/Io0mAXjMk8QoQY8WZbbD" alt=""><figcaption></figcaption></figure> <figure><img src="/files/WQ3BaXlxixP1v9XfEOfs" alt=""><figcaption></figcaption></figure></div>

Remove the 2 T-20 screws and take out the bottom cover.

<div><figure><img src="/files/Fq28rj2HD4p2XYjWUpdD" alt=""><figcaption></figcaption></figure> <figure><img src="/files/rV2pv50eWEMTMeto0IMw" alt=""><figcaption></figcaption></figure></div>

### Step 3 - Install the Gear and Turn Signal Stalk

Slide the gear stalk / turn signal stalk into the bracket. Tighten the screw on the right bracket to secure the stalk.

<figure><img src="/files/EHmCL3pugghE1BcuKejs" alt="" width="563"><figcaption></figcaption></figure>

### Step 4 - Install the Gear Stalk Bracket

Install the 2 brackets with stalks on the steering column. Use the 2 retainers to connect both brackets at the top and bottom.

<div><figure><img src="/files/UcsxNHASC0lXBO3qcBZ7" alt=""><figcaption></figcaption></figure> <figure><img src="/files/UnWnk8tA5I4A09aAn9NO" alt=""><figcaption></figcaption></figure></div>

### Step 5 - Wire Connection

Remove the A pillar kick panel on the right side (no matter you have a LHD or RHD car).

Connect the CAN connector and power connector respectively.

<div><figure><img src="/files/Men4awDf4Wa2y8DCkTwW" alt=""><figcaption><p>Power Connector</p></figcaption></figure> <figure><img src="/files/2PhpuQk1HO2dK8AgJv58" alt=""><figcaption><p>CAN Connector</p></figcaption></figure></div>

Run the wire up to the steering wheel column and connect to the stalks.

<figure><img src="/files/MDXMz3qRsb3VJhKi5ALD" alt="" width="563"><figcaption></figcaption></figure>

### Step 6 - Install the Covers

Slide in the bottom cover.&#x20;

<figure><img src="/files/gzn8nXHDWKAbWZKdBFtr" alt="" width="563"><figcaption></figcaption></figure>

Align the lower holes and secure the cover by Phillips screws.

<div><figure><img src="/files/Pkx16SY9F8m22dDBYHe3" alt=""><figcaption></figcaption></figure> <figure><img src="/files/wt4Bdm0xyRxupPsAEgEl" alt=""><figcaption></figcaption></figure></div>

Install the top cover.

<figure><img src="/files/J4pwz3Jf4Fvf1HtLOgWN" alt="" width="563"><figcaption></figcaption></figure>

Install the side covers below the gear stalk.

<div><figure><img src="/files/kARVt69qZ6lBRnL5qAYE" alt=""><figcaption></figcaption></figure> <figure><img src="/files/TFHNPDCqFEhWJX8Vq7IN" alt=""><figcaption></figcaption></figure></div>

### Step 7 - Finishing Up

Test the functionality of the gear and turn signal stalk. If everythings work properly, put the steering wheel and the airbag back to their original position.


---

# Agent Instructions: Querying This Documentation

If you need additional information that is not directly available in this page, you can query the documentation dynamically by asking a question.

Perform an HTTP GET request on the current page URL with the `ask` query parameter:

```
GET https://evoffer.gitbook.io/evoffer-installation-guide/model-3/gear-and-turn-signal-stalk.md?ask=<question>
```

The question should be specific, self-contained, and written in natural language.
The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.