> For the complete documentation index, see [llms.txt](https://evoffer.gitbook.io/evoffer-installation-guide/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://evoffer.gitbook.io/evoffer-installation-guide/model-3/gear-and-turn-signal-stalk.md).

# Gear and Turn Signal Stalk

This is the installation guide for Tesla Model 3 (2024+) Gear and Turn Signal Stalk from EVOffer.

{% embed url="<https://evoffer.com/product/model-3-2024-gear-turn-signal-stalk/>" %}

## Packing List

1.
2.
3. <br>

## Recommended Tools <a href="#recommended-tools" id="recommended-tools"></a>

1. Small Flathead Screwdriver
2. Phillips Screwdriver
3. T-20 Screwdriver
4. T-45 Screwdriver (with long wrench)

## Installation

### Step 1 - Remove the Steering Wheel

Insert a small flathead screwdriver into the 2 holes behind the steering wheel to pop out the airbag.

<div><figure><img src="/files/YhlmEUBRsfGzXSDwX4K2" alt=""><figcaption></figcaption></figure> <figure><img src="/files/ZS7akaBMwvzYN4GSxhom" alt=""><figcaption></figcaption></figure></div>

Disconnect the yellow and red connectors.&#x20;

<figure><img src="/files/g42m6MIyUJonSxLCGY7b" alt="" width="563"><figcaption></figcaption></figure>

Remove the center screw with a T-45 screw driver with long wrench.

<div><figure><img src="/files/11WK9MqfIlHYj8hHCdR7" alt=""><figcaption></figcaption></figure> <figure><img src="/files/0IyHGo1frkQBKiozJN6Q" alt=""><figcaption></figcaption></figure></div>

Take a picture of the center screw position. You can refer to this picture when you put the steering wheel back later. Remove the steering wheel afterwards.

<div><figure><img src="/files/RZ0EPJjURnmfYpuRWKLD" alt="" width="563"><figcaption></figcaption></figure> <figure><img src="/files/6THUEIik4QWZQiisTBTx" alt=""><figcaption></figcaption></figure></div>

### Step 2 - Remove the Steering Column Covers

Pull the top cover outward to release the cover.

<div><figure><img src="/files/Io0mAXjMk8QoQY8WZbbD" alt=""><figcaption></figcaption></figure> <figure><img src="/files/WQ3BaXlxixP1v9XfEOfs" alt=""><figcaption></figcaption></figure></div>

Remove the 2 T-20 screws and take out the bottom cover.

<div><figure><img src="/files/Fq28rj2HD4p2XYjWUpdD" alt=""><figcaption></figcaption></figure> <figure><img src="/files/rV2pv50eWEMTMeto0IMw" alt=""><figcaption></figcaption></figure></div>

### Step 3 - Install the Gear and Turn Signal Stalk

Slide the gear stalk / turn signal stalk into the bracket. Tighten the screw on the right bracket to secure the stalk.

<figure><img src="/files/EHmCL3pugghE1BcuKejs" alt="" width="563"><figcaption></figcaption></figure>

### Step 4 - Install the Gear Stalk Bracket

Install the 2 brackets with stalks on the steering column. Use the 2 retainers to connect both brackets at the top and bottom.

<div><figure><img src="/files/UcsxNHASC0lXBO3qcBZ7" alt=""><figcaption></figcaption></figure> <figure><img src="/files/UnWnk8tA5I4A09aAn9NO" alt=""><figcaption></figcaption></figure></div>

### Step 5 - Wire Connection

Remove the A pillar kick panel on the right side (no matter you have a LHD or RHD car).

Connect the CAN connector and power connector respectively.

<div><figure><img src="/files/Men4awDf4Wa2y8DCkTwW" alt=""><figcaption><p>Power Connector</p></figcaption></figure> <figure><img src="/files/2PhpuQk1HO2dK8AgJv58" alt=""><figcaption><p>CAN Connector</p></figcaption></figure></div>

Run the wire up to the steering wheel column and connect to the stalks.

<figure><img src="/files/MDXMz3qRsb3VJhKi5ALD" alt="" width="563"><figcaption></figcaption></figure>

### Step 6 - Install the Covers

Slide in the bottom cover.&#x20;

<figure><img src="/files/gzn8nXHDWKAbWZKdBFtr" alt="" width="563"><figcaption></figcaption></figure>

Align the lower holes and secure the cover by Phillips screws.

<div><figure><img src="/files/Pkx16SY9F8m22dDBYHe3" alt=""><figcaption></figcaption></figure> <figure><img src="/files/wt4Bdm0xyRxupPsAEgEl" alt=""><figcaption></figcaption></figure></div>

Install the top cover.

<figure><img src="/files/J4pwz3Jf4Fvf1HtLOgWN" alt="" width="563"><figcaption></figcaption></figure>

Install the side covers below the gear stalk.

<div><figure><img src="/files/kARVt69qZ6lBRnL5qAYE" alt=""><figcaption></figcaption></figure> <figure><img src="/files/TFHNPDCqFEhWJX8Vq7IN" alt=""><figcaption></figcaption></figure></div>

### Step 7 - Finishing Up

Test the functionality of the gear and turn signal stalk. If everythings work properly, put the steering wheel and the airbag back to their original position.