Auto Present Door Handles (RGB Edition)

This is the installation guide for Tesla Model 3 Auto Present Door Handles (RGB Edition) from EVOffer.

Model 3 Auto Present Door Handles (RGB Edition)EVOffer

User Manual

Model 3/Y Auto Present Door Handles (RGB Edition MARK 2.0)EVOffer User Guide

Packing List

1. Door Handle * 4

2. Signal Wire * 4

3. Power and CAN Wire * 1

4. Control Unit * 1

5. Zip Tie

6. Washer * 4

7. Spacer * 4 (For 2021+ Model 3 with Mexico Made Hall Sensor Only)

Recommended Tools

1. 8mm Hex Socket

2. 10mm Hex Socket

3. 13mm Hex Socket

4. T-20 Screwdriver

5. T-30 Screwdriver

6. Wrench

7. Small Flathead Screwdriver

8. Pry Tool

9. Electrical Tape

10. Diagonal Cutting Pliers

11. Wire Fishing Tool

Installation

Step 1 - Run the ECU Harness

The ECU harness includes a CAN connector, a ground wire, and a power wire. Depending on the model year of your car, you'll connect the power, ground, and CANbus in different locations:

For Models from 2020 or Earlier (Variant A):

If your car is a 2020 model or earlier, follow these guidelines to connect the power:

pageElectric Tailgate (MARK 2)

Connect the ground to car chassis.

For the canbus, we will update the manual soon.

For Models from 2021 or Later (Variant B):

If your car is a 2021 model or later, follow these steps:

On the right side of the car (the image below shows the left side, but you should work on the right side), release the upper clip that attaches the middle A-Pillar trim to the vehicle. Then, pull the trim upwards to remove it.

Release the topmost clip on the lower A-pillar trim.

Pull the rearmost part of the lower A-pillar trim upward to release the clips and tabs. Then, pull the entire trim rearward to remove it from the vehicle.

On the ECU harness, you'll need to connect the power and the CANbus:

The ground wire is embedded into the CAN connector for MARK 2.0 system. You don't need to connect it separately.

For the power and ground, route the red and black wires to the frunk through the firewall. Connect the power to the 12v battery (For 2022+ models, strip the end of the red wire and wrap it around the jump post).

Firewall location, circled in Yellow. It should be on the right side of the MCU for LHD car

You'll find a large white connector in the harness. Connect this to the blue idle connector located behind the kick panel near the door on the right side of the car.

Location of the blue connector

Step 2 - Run the Signal Wires into each Door

The markings on the four wires are based on the assumption that the ECU is mounted on the right side of the car. If you place your ECU on the left side (as in models from 2020 or earlier), then swap the left and right harnesses. Run the harnesses into each door.

Step 3 - Remove the Door Panel and Window

Follow the guide below to remove door panel and window.

pageDoor Panel and Window Removal

Step 4 - Remove the OEM Door Handle

Front Door

Remove the plugs that cover access to the door handle nuts.

Disconnect the hall sensor connector

Remove the nuts that attach the door handle to the door, and then remove the handle from the door. (10mm socket)

Now you can remove the door handle assembly

Rear Door

Disconnect the hall sensor connector.

Remove the plugs that cover access to the door handle nuts.

Another plug is not shown in the picture. It's the circular plug above the one in the picture

Remove the nuts that attach the door handle to the door, and then remove the handle from the door. (10mm socket)

Step 5 - Replace the Handle

Remove the 2 screws holding the hall sensor. It should be either T-15 or T-20 depending on different model years.

Transfer the hall sensor to the replacement handle and reassemble it onto the door. Inspect the hall sensor; if it has a "CN" mark printed on it, there's no need to place a washer behind the sensor. If it doesn't have a "CN" mark, it's a Mexico hall sensor, and you should place a spacer behind it. Afterward, retighten the screw.

Step 6 - Test the handle

Reconnect the OEM connector to the handle and connect the wire that runs into the door panel. On the ECU side, ensure the connector for the corresponding door is plugged in.

Test the handle for the following functions:

1. Press on the tip of the handle; the handle should pop out.

2. Pull on the handle; it should unlatch the lock, and then the handle should retract.

Ensure the handle moves smoothly when it pops out and retracts. If it doesn't, try adjusting the handle's position.

Before you close the door, if the window is installed back, make sure you connect the puddle light before testing, otherwise the windows trim can be damaged as the window will not go gown upon closing.

Step 7 - Reassemble the Door

Reassemble everything back.