> For the complete documentation index, see [llms.txt](https://evoffer.gitbook.io/evoffer-installation-guide/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://evoffer.gitbook.io/evoffer-installation-guide/model-s/plaid-style-yoke-steering-wheel.md).

# Plaid Style Yoke Steering Wheel

{% embed url="<https://evoffer.com/product/model-s-x-plaid-style-yoke-steering-wheel/>" %}

***

## Packing List

1. Steering Wheel Assembly
2. Airbag Assembly
3. Adapter Wire and Decoder
4. Airbag Wire

<div><figure><img src="/files/tynp1LOBYRKYeHs2OE6u" alt=""><figcaption></figcaption></figure> <figure><img src="/files/0BJWzQ4gj3DpGd8HzzPy" alt="" width="563"><figcaption></figcaption></figure></div>

## Recommended Tools

1. H-10 Screwdriver
2. T-10 Screwdriver
3. T-30 Screwdriver
4. Small Flat-head Screw Driver

## Precaution <a href="#precaution" id="precaution"></a>

Please turn off the power before installation started

1. Navigate the on-screen menu to the settings -> safety section
2. Power off the car. Make sure the screen goes black

{% hint style="danger" %}
DO NOT leave the seat once the steering wheel is removed. Otherwise error code may occur.
{% endhint %}

<div><figure><img src="/files/Ixzm8MxGEhFQI9CtI3OJ" alt="" width="563"><figcaption></figcaption></figure> <figure><img src="/files/QSuu6K5UglqNNj3LW7nU" alt="" width="563"><figcaption></figcaption></figure></div>

## Step 1 - Remove Steering Wheel and Airbag&#x20;

Move the steering wheel to the outmost & downmost position.

Use a T-30 wrench/socket to loosen the bolt securing the airbag and remove it from steering wheel.

<div><figure><img src="/files/avLmeOpfrWrtNsIBYITf" alt="" width="563"><figcaption></figcaption></figure> <figure><img src="/files/75RCqZfcmWlSVXIhDnz8" alt="" width="563"><figcaption></figcaption></figure></div>

Use a small flat-head screwdriver or similar tool to release the two connectors from the steering wheel hub.

<figure><img src="/files/wv9iFmCyMHVJ9EOTzQMh" alt="" width="563"><figcaption></figcaption></figure>

Remove the H-10 screw to release the steering wheel. Mark the position of the steering wheel if needed.

<figure><img src="/files/Q7ivfhQcZDJjcMP5uECy" alt="" width="563"><figcaption></figcaption></figure>

## Step 2 - Install the Decoder

Remove the plastic covers around the steering column.

<div><figure><img src="/files/URwNPXDwVR7ZYPgMzjLZ" alt="" width="563"><figcaption></figcaption></figure> <figure><img src="/files/wH76jtp52ZnsrJpAXghu" alt=""><figcaption></figcaption></figure></div>

Disconnect the yellow connector from the clock spring.

<figure><img src="/files/OnPRuD6OpTHzlKFTMPTy" alt="" width="390"><figcaption></figcaption></figure>

Remove the 3 T-10 bolts securing the clock spring assembly to the column. Take out the clock spring assembly from the steering column.

<figure><img src="/files/3jeRbg9Afdxm6krXDUPn" alt="" width="509"><figcaption></figcaption></figure>

Locate and connect the small white connector on the original clock spring housing that corresponds to the smaller plug on the new accessory harness.&#x20;

<figure><img src="/files/Oo0Dczk7xRdgiEIAMaes" alt="" width="563"><figcaption></figcaption></figure>

Plug the 4-pin connector (white/multi-colored wires) from the new accessory harness into the location on the clock spring housing where you just removed the original connector.&#x20;

<figure><img src="/files/bRsWRwN724zAwwlDerRz" alt="" width="563"><figcaption></figcaption></figure>

Connect the ribbon cable side of the decoder to the corresponding large white connector on the clock spring assembly.&#x20;

<figure><img src="/files/c9MI0evb8F9teC9q7OpE" alt="" width="563"><figcaption></figcaption></figure>

Secure the decoder to a flat surface on the clock spring using the double-sided tape on the back of the board.&#x20;

<div><figure><img src="/files/mDPp4JR56sGsQT9LU6m2" alt=""><figcaption></figcaption></figure> <figure><img src="/files/5Udsh3tuJRVTX9y9ZDXG" alt=""><figcaption></figcaption></figure></div>

Tidy up the wires and connect the yellow wire from the new harness into the existing wiring on the steering column.

<div><figure><img src="/files/kCojyNDCTL7uftf14jZH" alt=""><figcaption></figcaption></figure> <figure><img src="/files/TeXM1vgFekYdQKJhqXxq" alt=""><figcaption></figcaption></figure></div>

## Step 3 - Reassemble Steering Wheel and Airbag

Reinstall the clock spring assembly and secure it with the 3 T-10 bolts.

<div><figure><img src="/files/sw7WMChF6a2rM9yPyuee" alt=""><figcaption></figcaption></figure> <figure><img src="/files/XWYKVquFqxARKdg6fxLe" alt=""><figcaption></figcaption></figure></div>

Connect the yellow connector from the car to our adapter wire and reinstall the steering column covers.

<div><figure><img src="/files/qSD72NAAuRFRZZe8bg1D" alt=""><figcaption></figcaption></figure> <figure><img src="/files/JisRzKTyqtmt3yhrJTd4" alt=""><figcaption></figcaption></figure></div>

Install the new Yoke steering wheel.

<figure><img src="/files/T51lko2tPk2LrN1CDanx" alt="" width="563"><figcaption></figcaption></figure>

Secure the steering wheel with the the H-10 screw.

<figure><img src="/files/A1iLvHficqXE8J3ulDBF" alt="" width="563"><figcaption></figcaption></figure>

Connect the yellow airbag wire to the 4-th pin on the yellow plug.

<div><figure><img src="/files/u3dmQnikXy1Xh8zmWyMd" alt=""><figcaption></figcaption></figure> <figure><img src="/files/D8rCKv2HX3ocEk8OdEVy" alt=""><figcaption></figcaption></figure></div>

Connect the white airbag connector.

<figure><img src="/files/oAZ0VX8rr7oSiSCFrRO4" alt="" width="521"><figcaption></figcaption></figure>

Reconnect the 2 connectors.

<figure><img src="/files/qU6sNlfk0uEUNHew04Cr" alt="" width="563"><figcaption></figcaption></figure>

Align and firmly press the airbag module back into the center of the yoke steering wheel until it clicks into place.

<figure><img src="/files/uQzHh36VhUHsivI2L2oI" alt="" width="563"><figcaption></figcaption></figure>

## **Finishing Up**

Press the brake to turn on the car.&#x20;

Check if all the features and buttons on the steering wheel are working properly.