# Electric Tailgate

{% embed url="<https://evoffer.com/product/mg4-electric-tailgate/>" %}

{% hint style="info" %}

#### Pre-Installation Notes

* After installation, the decoder must be matched by adjusting the tailgate to the highest point, pressing the tail button for 5 seconds, and releasing after a long sound. This completes the matching operation (power replacement operation).
* The manual does not specify wiring, as installation does not require it.
  {% endhint %}

## Feature

<table><thead><tr><th>/</th><th data-type="checkbox">Open</th><th data-type="checkbox">Close</th></tr></thead><tbody><tr><td>External Release</td><td>true</td><td>false</td></tr><tr><td>Add-on Trunk Button</td><td>false</td><td>true</td></tr><tr><td>Add-on Driver Button *</td><td>true</td><td>true</td></tr><tr><td>Key Fob **</td><td>true</td><td>true</td></tr></tbody></table>

\* Long Press the button to open

\*\* Long Press the button to open and close

## Settings

### Speed Setting

The tailgate switch speed can be adjusted across five settings, with the default set to gear 4, the lowest at gear 2, and the highest at gear 6. To adjust:

1. Press and hold the add-on trunk button.
2. Listen for the buzzer. Two consecutive sounds indicate gear 2 is set, three sounds for gear 3, and so on.

### Height Settings

To adjust the tailgate to the desired height:

1. Bring the tailgate to the appropriate height.
2. Press and hold the add-on trunk button for 5 seconds until you hear a beep, indicating successful height setting.
3. The tailgate will open to this preset height on subsequent uses.

## Installation

### **Trim Panel Removal**

Remove the original trim panel as indicated by arrows in the figure.

<figure><img src="https://1282343728-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FHMP3br8kE8gv6TahPeL3%2Fuploads%2FlnzJc51mCNNxMyzSfc7G%2F1.jpg?alt=media&#x26;token=50df4899-9078-48fb-b436-63adcc49da43" alt=""><figcaption></figcaption></figure>

### **Strut Removal**

Use a flat screwdriver to tilt up the ball head steel sheet and remove the left and right struts of the original car.

<div data-full-width="false"><figure><img src="https://1282343728-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FHMP3br8kE8gv6TahPeL3%2Fuploads%2FlqsXDRC2oqktGanGWBGP%2F2-1.jpg?alt=media&#x26;token=3002c493-375d-4a98-aa9d-ec6b36d89d85" alt="" width="375"><figcaption></figcaption></figure></div>

<figure><img src="https://1282343728-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FHMP3br8kE8gv6TahPeL3%2Fuploads%2FI8kTVMMEeXKjt6WKg59I%2F2-2.jpg?alt=media&#x26;token=a2c053df-208b-4105-80cd-2249697e0c37" alt="" width="375"><figcaption></figcaption></figure>

### **Bracket Installation**

Remove the original car body bracket and install our distribution bracket (identical for left and right).

<figure><img src="https://1282343728-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FHMP3br8kE8gv6TahPeL3%2Fuploads%2FVVLRPLjc4RMHPxnOx0Pg%2F3-1.jpg?alt=media&#x26;token=d232d712-7edb-4270-b05a-8f2fb61ecd24" alt="" width="375"><figcaption></figcaption></figure>

<figure><img src="https://1282343728-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FHMP3br8kE8gv6TahPeL3%2Fuploads%2Fwlo9vcN80gYHLDyyoybY%2F3-2.jpg?alt=media&#x26;token=a6875271-390e-4bc6-81f3-6b95644c337c" alt="" width="375"><figcaption></figcaption></figure>

**Electric Strut Installation**

Refer to the schematic diagram for installation. Ensure the pole ball head card is properly placed and the strut line faces the body.

<figure><img src="https://1282343728-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FHMP3br8kE8gv6TahPeL3%2Fuploads%2FFI3rCqM4LZgAWlEqDyjz%2F4-1.jpg?alt=media&#x26;token=c418c381-646c-4ed1-913d-9a7eed7b910b" alt="" width="375"><figcaption></figcaption></figure>

<figure><img src="https://1282343728-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FHMP3br8kE8gv6TahPeL3%2Fuploads%2F1Juz2Vons0KzVPhUQ4ev%2F4-2.jpg?alt=media&#x26;token=b1140ae4-a549-47d7-8cc0-cc5c411a3fb8" alt="" width="375"><figcaption></figcaption></figure>

### **Stay Line Routing**

Pass the stay line (left and right) through the reserved hole of the original vehicle.

<figure><img src="https://1282343728-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FHMP3br8kE8gv6TahPeL3%2Fuploads%2FUxpJkvDu3As4ICTCPk2g%2F5.jpg?alt=media&#x26;token=54e02f04-fc1c-442d-98ce-7b3b73661aef" alt=""><figcaption></figcaption></figure>

### **Lower Suction Lock Installation**

Remove the original lock block and install the lower suction lock.

<figure><img src="https://1282343728-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FHMP3br8kE8gv6TahPeL3%2Fuploads%2F0rrB2wSfQeosxNnpouXT%2F6.jpg?alt=media&#x26;token=0b5d764a-efa7-49b0-a9c3-97fd6450c137" alt=""><figcaption></figcaption></figure>

### **Self-Priming Lock Installation**

Install on the left side of the trunk.

<figure><img src="https://1282343728-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FHMP3br8kE8gv6TahPeL3%2Fuploads%2Fz5oUvxxlKxHpHsNIVooo%2F7.jpg?alt=media&#x26;token=a7f7d674-5c78-42c1-bf5a-9593844648e9" alt=""><figcaption></figcaption></figure>

### **Lock Block Plug Connection**

Unplug the original car lock block plug and connect with the distribution plug.

<figure><img src="https://1282343728-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FHMP3br8kE8gv6TahPeL3%2Fuploads%2F68ej6cUtfRP46kmAj8wy%2F8.jpg?alt=media&#x26;token=9c86ef98-eefd-4e7e-9c10-2e7a287e5bd0" alt=""><figcaption></figcaption></figure>

### **Ground Position**

Locate under the right rear door foot pedal.

<figure><img src="https://1282343728-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FHMP3br8kE8gv6TahPeL3%2Fuploads%2F2n7GZA8Z3Ak8X2puahQ2%2F9.jpg?alt=media&#x26;token=e1d5398a-fcff-4ccb-8cba-cf0d96f27a98" alt=""><figcaption></figcaption></figure>

### **Electrical Connection**

Take the electrical position in the center console under the main driver to find the safety box. Connect to 12V normal power with insurance over 20A.

<figure><img src="https://1282343728-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FHMP3br8kE8gv6TahPeL3%2Fuploads%2FAAKbI71KZjGciMUwL8UB%2F10.jpg?alt=media&#x26;token=13f0fe16-9856-4e07-9f2d-61d0a90f588b" alt=""><figcaption></figcaption></figure>

### **Controller Securing**

Secure the controller to the left of the tailgate.

<figure><img src="https://1282343728-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FHMP3br8kE8gv6TahPeL3%2Fuploads%2FUTVHohw3ze8SGIaQpMNG%2F11.jpg?alt=media&#x26;token=63fbe03e-1571-46d6-9a31-67e7ea0e0c09" alt=""><figcaption></figcaption></figure>

### **Front Button Installation**

Install the front button in the opening of the main driver's center console as shown.

<figure><img src="https://1282343728-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FHMP3br8kE8gv6TahPeL3%2Fuploads%2FrRQLcJgIroUmtYScmKk4%2F12.jpg?alt=media&#x26;token=ee58360a-d65e-4d98-a02b-c2ab8b533a83" alt=""><figcaption></figcaption></figure>

### **Rear Button Installation**

After making a hole in the tailgate trim panel below, install the rear button.

<figure><img src="https://1282343728-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FHMP3br8kE8gv6TahPeL3%2Fuploads%2FQm4UT4Lkyd24PJ4eK9PP%2F13.jpg?alt=media&#x26;token=aef9248b-996c-4dc5-9962-036dc14db5f6" alt=""><figcaption></figcaption></figure>

### **Line Positioning**

Ensure all lines are correctly positioned and secured.

<figure><img src="https://1282343728-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FHMP3br8kE8gv6TahPeL3%2Fuploads%2FbY5GFmR7Gs3w2dGDArHu%2F15.jpg?alt=media&#x26;token=887a6d37-5788-4c84-aad8-a5c00e544e65" alt=""><figcaption></figcaption></figure>

### **Testing**

After installation, test all functions to ensure proper operation.

{% hint style="info" %}

### Note

The installation instructions may differ slightly from actual operation. If in doubt, please operate according to the actual situation or contact us for assistance.
{% endhint %}